Selenium oxychloride

H301 (100%): Toxic if swallowed [Danger Acute toxicity, oral]

H314 (90.7%): Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]

H331 (100%): Toxic if inhaled [Danger Acute toxicity, inhalation]

H373 (100%): May causes damage to organs through prolonged or repeated exposure [Warning Specific target organ toxicity, repeated exposure]

H400 (100%): Very toxic to aquatic life [Warning Hazardous to the aquatic environment, acute hazard]

H410 (100%): Very toxic to aquatic life with long lasting effects [Warning Hazardous to the aquatic environment, long-term hazard]

P260, P261, P264, P270, P271, P273, P280, P301+P316, P301+P330+P331, P302+P361+P354, P304+P340, P305+P354+P338, P316, P319, P321, P330, P363, P391, P403+P233, P405, and P501 (click each P-code to see the statement)

Aggregated GHS information provided per 43 reports by companies from 3 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.

Information may vary between notifications depending on impurities, additives, and other factors. The percentage value in parenthesis indicates the notified classification ratio from companies that provide hazard codes. Only hazard codes with percentage values above 10% are shown. For more detailed information, please visit ECHA C&L website.

Fresh air, rest. Half-upright position. Artificial respiration may be needed. Refer for medical attention.

Remove contaminated clothes. Rinse skin with plenty of water or shower. Refer for medical attention .

First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.

Rinse mouth. Do NOT induce vomiting. Refer for medical attention .

Signs and Symptoms of Selenium Oxychloride Exposure: Signs and symptoms of acute exposure to selenium oxychloride may include dermatitis and burns to the skin, eye and nasal irritation, a burning sensation in the nostrils, headache, a garliclike odor on the breath, fever, nausea, and vomiting (coffee grounds in appearance). Irritation of the gastrointestinal tract may also be observed. Lassitude, dizziness, hypotension (low blood pressure), decreased peripheral pulse, dyspnea (difficulty in breathing), pulmonary edema, cardiopulmonary arrest, and coma have also been reported.

Emergency Life-Support Procedures: Acute exposure to selenium oxychloride may require decontamination and life support for the victims. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.

Inhalation Exposure:

1. Move victims to fresh air. Emergency personnel should avoid self-exposure to selenium oxychloride.

2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer 100% humidified oxygen or other respiratory support.

3. Obtain authorization and/or further instructions from the local hospital for performance of other invasive procedures.

4. Rush to a health care facility.

Dermal/Eye Exposure:

1. Remove victims from exposure. Emergency personnel should avoid self-exposure to selenium oxychloride.

3. Remove contaminated clothing as soon as possible.

4. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.

5. Wash exposed skin areas thoroughly with soap and water.

6. Obtain authorization and/or further instructions from the local hospital for performance of other invasive procedures.

7. Rush to a health care facility.

Ingestion Exposure:

1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer 100% humidified oxygen or other respiratory support.

2. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.

3. DO NOT induce vomiting.

4. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.

5. Promote excretion by administering a saline cathartic or sorbitol to conscious and alert victims. Children require 15 to 30 g (1/2 to 1 oz) of cathartic; 50 to 100 g (1-3/4 to 3-1/2 oz) is recommended for adults.

6. Rush to a health care facility. (EPA, 1998)

General First Aid:

· Call 911 or emergency medical service.

· Ensure that medical personnel are aware of the material(s) involved, take precautions to protect themselves and avoid contamination.

· Move victim to fresh air if it can be done safely.

· Administer oxygen if breathing is difficult.

· If victim is not breathing:

-- DO NOT perform mouth-to-mouth resuscitation; the victim may have ingested or inhaled the substance.

-- If equipped and pulse detected, wash face and mouth, then give artificial respiration using a proper respiratory medical device (bag-valve mask, pocket mask equipped with a one-way valve or other device).

-- If no pulse detected or no respiratory medical device available, provide continuous compressions. Conduct a pulse check every two minutes or monitor for any signs of spontaneous respirations.

· Remove and isolate contaminated clothing and shoes.

· For minor skin contact, avoid spreading material on unaffected skin.

· In case of contact with substance, remove immediately by flushing skin or eyes with running water for at least 20 minutes.

· For severe burns, immediate medical attention is required.

· Effects of exposure (inhalation, ingestion, or skin contact) to substance may be delayed.

· Keep victim calm and warm.

Cool containers that are exposed to flames with water until well after the fire is out. Stay upwind; keep out of low areas. Wear positive pressure breathing apparatus and special protective clothing.

Use dry chemical, carbon dioxide, water spray, or foam for small fires; use water spray, fog, or foam for large fires. (EPA, 1998)

In case of fire in the surroundings, use appropriate extinguishing media.

If material on fire or involved in fire: Extinguish fire using agent suitable for type of surrounding fire. Material itself does not burn or burns with difficulty. Use dry chemical, dry sand, or carbon dioxide. Do not use water on material itself. If large quantities of combustibles are involved, use water in flooding quantities as spray and fog. Keep run-off water out of sewers and water sources. Use water spray to knock down vapors.

Wear appropriate chemical protective gloves, boots, and goggles. Wear positive pressure self-contained breathing apparatus when fighting fires involving this material. If contact with the material is anticipated, wear appropriate chemical protective clothing.

· CALL 911. Then call emergency response telephone number on shipping paper. If shipping paper not available or no answer, refer to appropriate telephone number listed on the inside back cover.

· Keep unauthorized personnel away.

· Stay upwind, uphill and/or upstream.

· Ventilate closed spaces before entering, but only if properly trained and equipped.

· ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area.

· All equipment used when handling the product must be grounded.

· Do not touch damaged containers or spilled material unless wearing appropriate protective clothing.

· Stop leak if you can do it without risk.

· A vapor-suppressing foam may be used to reduce vapors.

· DO NOT GET WATER INSIDE CONTAINERS.

· Use water spray to reduce vapors or divert vapor cloud drift. Avoid allowing water runoff to contact spilled material.

· Prevent entry into waterways, sewers, basements or confined areas.

Small Spill

· Cover with DRY earth, DRY sand or other non-combustible material followed with plastic sheet to minimize spreading or contact with rain.

· Use clean, non-sparking tools to collect material and place it into loosely covered plastic containers for later disposal.

Excerpt from ERG Guide 157 [Substances - Toxic and/or Corrosive (Non-Combustible / Water-Sensitive)]:

IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.

SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.

FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)

Immediate precautionary measure

· Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.

· For highlighted materials: see Table 1 - Initial Isolation and Protective Action Distances.

· For non-highlighted materials: increase the immediate precautionary measure distance, in the downwind direction, as necessary.

· If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions.

Personal protection: complete protective clothing including self-contained breathing apparatus. Ventilation. Collect leaking and spilled liquid in sealable containers as far as possible. Absorb remaining liquid in dry sand or inert absorbent. Then store and dispose of according to local regulations.

SRP: Wastewater from contaminant suppression, cleaning of protective clothing/equipment, or contaminated sites should be contained and evaluated for subject chemical or decomposition product concentrations. Concentrations shall be lower than applicable environmental discharge or disposal criteria. Alternatively, pretreatment and/or discharge to a permitted wastewater treatment facility is acceptable only after review by the governing authority and assurance that "pass through" violations will not occur. Due consideration shall be given to remediation worker exposure (inhalation, dermal and ingestion) as well as fate during treatment, transfer and disposal. If it is not practicable to manage the chemical in this fashion, it must be evaluated in accordance with EPA 40 CFR Part 261, specifically Subpart B, in order to determine the appropriate local, state and federal requirements for disposal.

Environmental considerations: Air spill: Apply water spray or mist to knock down vapors.

Environmental considerations: Water spill: Use natural barriers or oil spill control booms to limit spill travel. Remove trapped material with suction hoses.

Environmental considerations: Land spill: Dig a pit, pond, lagoon, holding area to contain liquid or solid material. /SRP: If time permits, pits, ponds, lagoons, soak holes, or holding areas should be sealed with an impermeable flexible membrane liner./ Dike surface flow using soil, sand bags, foamed polyurethane, or foamed concrete. Absorb bulk liquid with fly ash, cement powder, or commerical sorbents. /Selenium oxychloride, poisonous liquid, N.O.S./

1. Ventilate area of spill. 2. Collect spilled material in most convenient & safe manner & deposit in sealed containers for reclamation or for disposal in a secured sanitary landfill. Liq containing selenium & its inorganic cmpd should be absorbed in vermiculite, dry sand, earth, or similar material.

Generators of waste (equal to or greater than 100 kg/mo) containing this contaminant, EPA hazardous waste number D010, must conform with USEPA regulations in storage, transportation, treatment and disposal of waste.

If material not on fire and not involved in fire: Keep material out of water sources and sewers. Neutralize spilled material with crushed limestone, soda ash, or lime.

Personnel protection: Avoid breathing dusts, and fumes from burning material. Keep upwind. Avoid bodily contact with the material. Do not handle broken packages unless wearing appropriate personal protective equipment. Wash away any material which may have contacted the body with copious amounts of soap and water.

SRP: Contaminated protective clothing should be segregated in such a manner so that there is no direct personal contact by personnel who handle, dispose, or clean the clothing. The completeness of the cleaning procedures should be considered before the decontaminated protective clothing is returned for reuse by the workers. Contaminated clothing should not be taken home at the end of shift, but should remain at employee's place of work for cleaning.

SRP: Wastewater from contaminant suppression, cleaning of protective clothing/equipment, or contaminated sites should be contained and evaluated for subject chemical or decomposition product concentrations. Concentrations shall be lower than applicable environmental discharge or disposal criteria. Alternatively, pretreatment and/or discharge to a permitted wastewater treatment facility is acceptable only after review by the governing authority and assurance that "pass through" violations will not occur. Due consideration shall be given to remediation worker exposure (inhalation, dermal and ingestion) as well as fate during treatment, transfer and disposal. If it is not practicable to manage the chemical in this fashion, it must be evaluated in accordance with EPA 40 CFR Part 261, specifically Subpart B, in order to determine the appropriate local, state and federal requirements for disposal.

For more Preventive Measures (Complete) data for SELENIUM OXYCHLORIDE (11 total), please visit the HSDB record page.

Excerpt from ERG Guide 157 [Substances - Toxic and/or Corrosive (Non-Combustible / Water-Sensitive)]:

ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. All equipment used when handling the product must be grounded. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. A vapor-suppressing foam may be used to reduce vapors. DO NOT GET WATER INSIDE CONTAINERS. Use water spray to reduce vapors or divert vapor cloud drift. Avoid allowing water runoff to contact spilled material. Prevent entry into waterways, sewers, basements or confined areas.

SMALL SPILL: Cover with DRY earth, DRY sand or other non-combustible material followed with plastic sheet to minimize spreading or contact with rain. Use clean, non-sparking tools to collect material and place it into loosely covered plastic containers for later disposal. (ERG, 2024)

Separated from metal oxides, strong bases and food and feedstuffs. Dry. Ventilation along the floor.

· Wear positive pressure self-contained breathing apparatus (SCBA).

· Wear chemical protective clothing that is specifically recommended by the manufacturer when there is NO RISK OF FIRE.

· Structural firefighters' protective clothing provides thermal protection but only limited chemical protection.

0.02 [mg/m3], as Se, inhalable fraction[German Research Foundation (DFG)]

0.91 [mg/m3]

10 [mg/m3]

60 [mg/m3]

0.2 [mg/m3], as Se

1.0 [mg/m3], as Se

8 hr Time Weighted Avg (TWA): 0.2 mg/cu m. /Selenium and compounds, as Se/

Excursion Limit Recommendation: Excursions in worker exposure levels may exceed 3 times the TLV-TWA for no more than a total of 30 minutes during a work day, and under no circumstances should they exceed 5 times the TLV-TWA, provided that the TLV-TWA is not exceeded. /Selenium and compounds, as Se/

0.2 mg/m

(as Se, inhalable fraction): 0.02 mg/m

Chronic Oral: 0.005 mg/kg/day (L134)

· Note: Some foams will react with the material and release corrosive/toxic gases.

Small Fire

· CO2 (except for Cyanides), dry chemical, dry sand, alcohol-resistant foam.

Large Fire

· Water spray, fog or alcohol-resistant foam.

· If it can be done safely, move undamaged containers away from the area around the fire.

· Avoid aiming straight or solid streams directly onto the product.

· Dike runoff from fire control for later disposal.

Fire Involving Tanks, Rail Tank Cars or Highway Tanks

· Fight fire from maximum distance or use unmanned master stream devices or monitor nozzles.

· Do not get water inside containers.

· Cool containers with flooding quantities of water until well after fire is out.

· Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank.

· ALWAYS stay away from tanks in direct contact with flames.

A harmful contamination of the air can be reached rather quickly on evaporation of this substance at 20 °C.

The substance is corrosive to the eyes, skin and respiratory tract. Inhalation of the vapour may cause lung oedema. Medical observation is indicated.

Repeated or prolonged contact may cause skin sensitization. The substance may have effects on the respiratory tract, gastrointestinal tract, central nervous system and liver. This may result in nasal irritation, persistent garlic odour, stomach pain, nervousness and liver impairment.

For emergency situations, wear a positive pressure, pressure-demand, full facepiece self-contained breathing apparatus (SCBA) or pressure- demand supplied air respirator with escape SCBA and a fully-encapsulating, chemical resistant suit. (EPA, 1998)

Wear appropriate personal protective clothing to prevent skin contact. /Selenium/

Facilities for quickly drenching the body should be provided within the immediate work area for emergency use where there is a possibility of exposure. [Note: It is intended that these facilities provide a sufficient quantity or flow of water to quickly remove the substance from any body areas likely to be exposed. The actual determination of what constitutes an adequate quick drench facility depends on the specific circumstances. In certain instances, a deluge shower should be readily available, whereas in others, the availability of water from a sink or hose could be considered adequate.] /Selenium/

Respirator Recommendations: Up to 1 mg/cu m: /Selenium/ [Table#1970]

Respirator Recommendations: Emergency or planned entry into unknown concentrations or IDLH conditions: /Selenium/ [Table#1971]

Respirator Recommendations: Escape conditions: /Selenium/ [Table#1972]

STRICT HYGIENE!

Use ventilation, local exhaust or breathing protection.

Protective gloves. Protective clothing.

Selenium oxychloride appears as a colorless to light-colored liquid. Insoluble in water and denser than water. Contact may severely irritate skin, eyes and mucous membranes. May be toxic by ingestion, inhalation and skin absorption. Used to make other chemicals.

Nearly colorless or yellowish liquid. [HSDB]

YELLOWISH OR COLOURLESS LIQUID.

Nearly colorless or yellowish liquid

Pungent odor

356 °F at 760 mmHg (EPA, 1998)

176.4 °C

176.4 °C @760 [mm Hg]

47.3 °F (EPA, 1998)

Miscible with carbon tetrachloride, chloroform, carbon disulfide, benzene, toluene

Solubility in water at 20 °C: decomposes

Solubility in water: reaction

2.44 at 60.8 °F (EPA, 1998) - Denser than water; will sink

2.44 g/cu cm at 16 °C/4 °C

Relative density (water = 1): 2.42

2.42 @ 22°C

5.7 (air = 1)

1 mmHg at 94.6 °F (EPA, 1998)

0.05 [mmHg]

1 mm Hg at 34.8 °C

Vapor pressure, Pa at 34.8 °C: 132

2.9 [mm Hg] @25 °C

It is decomposed by water to form hydrochloric acid, a corrosive material.

When heated to decomposition ... emits very toxic fumes of /hydrogen chloride and selenium/.

Corrosive

Index of refraction: 1.651 at 20 °C/D

Critical volume = 235 cu cm/mol

Hydrolyzes to hydrochloric acid

Reactive with water

Solidifies at about 5 °C; decomposed by water into hydrochloric acid and selenious acid; fumes in air

Dielectric constant: 46.2 at 293.2 K

Other Classes -> Other Inorganic Compounds

Corrosives

Reactive agents - 2nd degree

Fumes in air. Insoluble in water and denser than water. Decomposed in water or moist air to form hydrochloric acid and selenious acid [Merck 11th ed. 1989].

Acyl Halides, Sulfonyl Halides, and Chloroformates

Water-Reactive

Air-Reactive

Red phosphorus reacts in the cold with SELENIUM OXYCHLORIDE evolving light and heat; white phosphorus reacts explosively [Mellor 10:906 1946-47]. When potassium is brought into contact with selenium oxychloride in the cold, an explosion occurs [Mellor 10:908 1946-47]. May react vigorously or explosively if mixed with diisopropyl ether or other ethers in the presence of trace amounts of metal salts [J. Haz. Mat., 1981, 4, 291]. Powdered antimony ignites on contact with the chloride, [Mellor, 1947, Vol. 10, 906]. With metal oxides, i.e. silver oxide, light is evolved and heat sufficient to decompose the mixture, [Mellor, 1947, Vol. 10, 909].

Red phosphorus evolves light & heat in contact with /seleninyl/ chloride while white phosphorus explodes.

In contact with silver oxide, light is evolved and sufficient heat to decompose some of it. Similar effects were observed with lead(II) oxide, lead(IV) oxide and lead (II)(IV) oxide.

Potassium explodes violently in contact with the liguid.

When potassium is brought in contact with selenium oxychloride in the cold, a violent explosion occurs.

For more Hazardous Reactivities and Incompatibilities (Complete) data for SELENIUM OXYCHLORIDE (7 total), please visit the HSDB record page.

Selenium readily substitutes for sulfur in biomolecules and in many biochemical reactions, especially when the concentration of selenium is high and the concentration of sulfur is low. Inactivation of the sulfhydryl enzymes necessary for oxidative reactions in cellular respiration, through effects on mitochondrial and microsomal electron transport, might contribute to acute selenium toxicity. Selenomethionine (a common organic selenium compound) also appears to randomly substitute for methionine in protein synthesis. This substitution may affect the structure and functionability of the protein, for example, by altering disulfide bridges. Inorganic forms of selenium appear to react with tissue thiols by redox catalysis, resulting in formation of reactive oxygen species and causing damage by oxidative stress. (L619)

3, not classifiable as to its carcinogenicity to humans. (L135)

Chronic oral exposure to high concentrations of selenium compounds can produce a disease called selenosis. The major signs of selenosis are hair loss, nail brittleness, and neurological abnormalities (such as numbness and other odd sensations in the extremities). Animal studies have shown that selenium may also affect sperm production and the female reproductive cycle. (L619)

The substance can be absorbed into the body by inhalation of its vapour and by ingestion.

Oral (L619) ; inhalation (L619) ; dermal (L619)

Burning sensation. Cough. Laboured breathing. Sore throat. Shortness of breath. Symptoms may be delayed.

Redness. Pain. Blisters. Skin burns.

Redness. Pain. Severe deep burns.

Burning sensation. Sore throat. Nausea. Abdominal cramps. Vomiting. Abdominal pain. Diarrhoea. Shock or collapse.

Short-term oral exposure to high concentrations of selenium may cause nausea, vomiting, and diarrhea. Brief exposures to high levels of elemental selenium or selenium dioxide in air can result in respiratory tract irritation, bronchitis, difficulty breathing, and stomach pains. Longer-term exposure to either of these air-borne forms can cause respiratory irritation, bronchial spasms, and coughing. (L619)

Neurotoxin - Other CNS neurotoxin

Occupational hepatotoxin - Secondary hepatotoxins: the potential for toxic effect in the occupational setting is based on cases of poisoning by human ingestion or animal experimentation.

Reproductive Toxin - A chemical that is toxic to the reproductive system, including defects in the progeny and injury to male or female reproductive function. Reproductive toxicity includes developmental effects. See Guidelines for Reproductive Toxicity Risk Assessment.

Dermatotoxin - Skin burns.

Skin Sensitizer - An agent that can induce an allergic reaction in the skin.

Toxic Pneumonitis - Inflammation of the lungs induced by inhalation of metal fumes or toxic gases and vapors.

Immediate first aid: Ensure that adequate decontamination has been carried out. If patient is not breathing, start artificial respiration, preferably with a demand-valve resuscitator, bag-valve-mask device, or pocket mask, as trained. Perform CPR as necessary. Immediately flush contaminated eyes with gently flowing water. Do not induce vomiting. If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain an open airway and prevent aspiration. Keep patient quiet and maintain normal body temperature. Obtain medical attention. /Selenium and Related Compounds/

Basic treatment: Establish a patent airway (oropharyngeal or nasopharyngeal airway, if needed). Suction if necessary. Watch for signs of respiratory insufficiency and assist ventilations if necessary. Administer oxygen by nonrebreather mask at 10 to 15 L/min. Monitor for shock and treat if necessary ... . Monitor for pulmonary edema and treat if necessary ... . Treat seizures if necessary ... . For eye contamination, flush eyes immediately with water. Irrigate each eye continuously with 0.9% saline (NS) during transport ... . Do not use emetics. For ingestion, rinse mouth and administer 5 mL/kg up to 200 mL of water for dilution if the patient can swallow, has a strong gag reflex, and does not drool. Administer activated charcoal ... . /Selenium and Related Compounds/

Advanced treatment: Consider orotracheal or nasotracheal intubation for airway control in the patient who is unconscious, has severe pulmonary edema, or is in severe respiratory distress. Positive-pressure ventilation techniques with a bag valve mask device may be beneficial. Consider drug therapy for pulmonary edema ... . Consider administering a beta agonist such as albuterol for severe bronchospasm ... .Monitor cardiac rhythm and treat arrhythmias if necessary ... . Start IV administration of D5W /SRP: "To keep open", minimal flow rate/. Use 0.9% saline (NS) or lactated Ringer's (LR) if signs of hypovolemia are present. For hypotension with signs of hypovolemia, administer fluid cautiously. Consider vasopressors if patient is hypotensive with a normal fluid volume. Watch for signs of fluid overload ... . Treat seizures with diazepam or lorazepam ... . Use proparacaine hydrochloride to assist eye irrigation ... . /Selenium and Related Compounds/

Emergency and supportive measures. Maintain an open airway and assist ventilation if necessary. Administer supplemental oxygen. Treat coma, convulsions, bronchospasm, hypotension, and pulmonary edema if they occur. Since hypotension is often multifactorial, evaluate and optimize volume status, peripheral vascular resistance, and myocardial contractility. Observe for at least 6 hours after exposure. ... /Selenium/

Decontamination: Inhalation. Immediately remove the victim from exposure and give supplemental oxygen if available. Skin and eyes. Remove contaminated clothing and wash exposed skin with soap and copious water. Irrigate exposed eyes with copious tepid water or saline. Ingestion. Ingestion of elemental selenium or selenium salts does not usually benefit from GI decontamination. In light of the risk of severe corrosive GI injury, gastric lavage plus activated charcoal may be of value for ingestion s of selenious acid seen within 1 hour. Invitro experiments indicate that vitamin C can reduce selenium salts to elemental selenium, which poorly absorbed. Its use has not been studied in vivo, but oral or nasogastric administration of several grams of ascorbic acid has been recommended. /Selenium/

/SIGNS AND SYMPTOMS/ Short-term Exposure: Inhalation of large quantities of ... selenium oxychloride may cause severe breathing difficulties which may not appear for several hours after exposure. Skin contact with ... selenium oxychloride may cause skin burns.

/SIGNS AND SYMPTOMS/ Selenium oxychloride readily destroys skin on contact, causing third degree burns unless immediately removed with water.

/SIGNS AND SYMPTOMS/ Contact with the skin can cause severe burns. It is toxic by skin absorption and by inhalation.

/SIGNS AND SYMPTOMS/ Selenium oxychloride is strongly vesicant and will rapidly destroy the skin upon contact unless immediately removed by washing.

For more Human Toxicity Excerpts (Complete) data for SELENIUM OXYCHLORIDE (8 total), please visit the HSDB record page.

/LABORATORY ANIMALS: Acute Exposure/ The minimum lethal dose, when applied to the skin of a rabbit, is 7 mg/kg.

... Applicants who will be working with more reactive ... cmpd such as ... selenium oxychloride should /be protected if they/ have had history of dermatitis, chronic bronchitis or any ... skin allergy of resp tract infection. Also those ... with history of liver or kidney disease, jaundice or albuminuria should be excluded. Careful consideration must be given to /SRP: protecting employees during their reproductive years/.

The substance is harmful to aquatic organisms.

Selenium oxychloride may enter the body through the skin.

... by skin absorption and by inhalation.

The substance is harmful to aquatic organisms.

Selenium oxychloride may enter the body through the skin.

... by skin absorption and by inhalation.

Generators of waste (equal to or greater than 100 kg/mo) containing this contaminant, EPA hazardous waste number D010, must conform with USEPA regulations in storage, transportation, treatment and disposal of waste.

/GUIDE 157: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE/WATER -SENSITIVE)/ Health: TOXIC; inhalation, ingestion or contact (skin, eyes) with vapors, dusts or substance may cause severe injury, burns, or death. Reaction with water or moist air will release toxic, corrosive or flammable gases. Reaction with water may generate much heat which will increase the concentration of fumes in the air. Fire will produce irritating, corrosive and/or toxic gases. Runoff from fire control or dilution water may be corrosive and/or toxic and cause pollution.

/GUIDE 157: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE/WATER -SENSITIVE)/ Fire or Explosion: Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes. Vapors may accumulate in confined areas (basement, tanks, hopper/tank cars etc.). Substance will react with water (some violently), releasing corrosive and/or toxic gases. Contact with metals may evolve flammable hydrogen gas. Containers may explode when heated or contaminated with water.

/GUIDE 157: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE/WATER -SENSITIVE)/ Public Safety: CALL Emergency Response Telephone Number ... As an immediate precautionary measure, isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids. Keep unauthorized personnel away. Stay upwind. Keep out of low areas. Ventilate enclosed areas.

/GUIDE 157: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE/WATER -SENSITIVE)/ Protective Clothing: Wear positive pressure self-contained breathing apparatus (SCBA). Wear chemical protective clothing that is specifically recommended by the manufacturer. It may provide little or no thermal protection. Structural firefighters' protective clothing provides limited protection in fire situations ONLY; it is not effective in spill situations where direct contact with the substance is possible.

For more DOT Emergency Guidelines (Complete) data for SELENIUM OXYCHLORIDE (8 total), please visit the HSDB record page.

UN 2879; Selenium oxychloride

IMO 8.1; Selenium oxychloride

UN 3440; Selenium compound, liquid, n.o.s

49 233 45; Selenium oxychloride

No person may /transport,/ offer or accept a hazardous material for transportation in commerce unless that person is registered in conformance ... and the hazardous material is properly classed, described, packaged, marked, labeled, and in condition for shipment as required or authorized by ... /the hazardous materials regulations (49 CFR 171-177)./

The International Air Transport Association (IATA) Dangerous Goods Regulations are published by the IATA Dangerous Goods Board pursuant to IATA Resolutions 618 and 619 and constitute a manual of industry carrier regulations to be followed by all IATA Member airlines when transporting hazardous materials.

The International Maritime Dangerous Goods Code lays down basic principles for transporting hazardous chemicals. Detailed recommendations for individual substances and a number of recommendations for good practice are included in the classes dealing with such substances. A general index of technical names has also been compiled. This index should always be consulted when attempting to locate the appropriate procedures to be used when shipping any substance or article.

Corrosive Poison

Do not transport with food and feedstuffs.

Symbol: T, N; R: 23/25-33-50/53; S: (1/2)-20/21-28-45-60-61; Note: A

UN Hazard Class: 8; UN Subsidiary Risks: 6.1; UN Pack Group: I